Model HS12 in-wall mounting frame provides the maximum support and facilitates the installation of dual bubbler RIVIVE™ series fountains and bottle fillers. Mounted during “rough-in” phase of construction, this mounting frame allows the dual fountains to be easily and quickly installed.

• One-piece 12 gauge heavy duty mounting plate is welded to the 18 gauge wall frame
• Heavy gauge galvanized steel construction provides a solid support system for these dual bubbler fountains that is not only sturdy but provides a certain amount of corrosion resistance as well.
• Wall opening size required is 31-1/8″ wide, 47-7/8″ high, and 6″ deep (75.1 x 121.6 x 15.2 cm)
• Power cord included

Model HS11 in-wall mounting frame provides the maximum support and facilitates the installation of single bubbler Rivive series fountains and bottle fillers. Mounted during “rough-in” phase of construction, this mounting frame allows the single bubbler fountains to be easily and quickly installed.

• One-piece 12 gauge heavy duty mounting plate is welded to the 18 gauge wall frame
• Heavy gauge galvanized steel construction provides a solid support system for these single bubbler fountains that is not only sturdy but provides corrosion resistance as well.
• Wall opening size required is 18-5/8″ wide, 47-7/8″ high, and 6″ deep (47.3 x 121.6 x 12.7 cm)
• Power cord included

Model 6434 replacement strainer is used with the Haws RIVIVE™ series bottle fillers and drinking fountains. Strainer mesh removes particles larger than 110 microns from the drinking water with a service life of 5 years. The strainer is designed to work with the RFID tracking system of the RIVIVE series bottle fillers.  System will detect that a strainer is installed, and does not require any additional programming or setup by the customer.

Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.

Model BP15WC is an optional back panel for use with the 1311/1920W and 1920WHO fountain/bottle filler combinations when child-height ADA requirements must be met. This back panel is 15″ x 22-1/4″ (38 x 54 cm) stainless steel with a white powder-coat finish.

Model BP15C is an optional back panel for use with the 1107 and 1109 fountain/1920 and 1920HO bottle filler combinations when child-height ADA requirements must be met. This back panel is 15″ x 22-1/4″ (38 x 54 cm) stainless steel with a satin finish.

Model 6480 drinking fountain bottle filler Filter kit includes a 3000 gallon carbon block filter, filter head, and mounting bracket. This kit allows filtration for virtually any drinking fountain or bottle filler. The filter reduces chlorine (taste and odor) and lead, and removes 99.99% of cysts. It is a carbon block filter cartridge with a service life of 1 year/3000-gallons (11356 L). Tested and certified by CSA against NSF/ANSI Standard 42 for the reduction of chlorine (taste and odor) and against NSF/ ANSI Standard 53 for the reduction of lead and cysts.

• High traffic area ready with a 3000-gallon (11,356 L) capacity filter
• 1/4 turn filter head allows changing of filter without turning off water supply
• 3000 gallon carbon block filter reduces chlorine (taste and odor) and lead, and removes 99.99% of cysts
• Universal Drinking Fountain Bottle Filler Filter Kit will work with almost any fountain or bottle filler (Optional model 6603 for in-wall installations with no rear access)

Model 6810W is an option for the 6800 in-wall support carrier produced after August of 2023. This custom-fit side drain port can be installed in the field to allow a waste drain to be installed outside of the carrier.

Model 1931 is a replacement sensor used for the motion-activated bottle filler portion of the Haws 1200 series water coolers. The vandal-resistant sensor resists scratching and water droplet fowling.

Model 6810 In-wall floor mounted fixture carrier: Two 2½” x 1½” x 1/8” thick structural steel uprights having 6” x 3″ x 3/8” thick welded steel 4-bolt floor flanges, supplied with ‘U’ bolts and hardware. For use in conjunction with Haws in-wall mounting plates 6700, 6700.4, 6710, 6715, 6717, or 6776, for extra heavy duty fixture support. Fits inside standard 2” x 4” wall construction. Suitable for use with either 3/8″ or 1/2″ concrete anchors (by others). Includes mounting holes for plumbing stub out bracket and electrical boxes, and a on-site custom-fit side drain port. This port can be placed at any height. Exceeds requirements when tested in accordance to ASME Standard A112.6.1M. Design was independently verified as suitable to meet HCAI and CBC anchor spacing requirements.

The Haws BTL1311 is an add-on bottle stand for the 1311/1501 series drinking fountains with the 1920 bottle filler option. Once installed, the user can place their bottle on the stand allowing the bottle to be filled with one hand (either by using the push button, or the motion-activated operation). The stand is made of 304 stainless-steel and is easily installed (see video under Resources).

The Haws BTL1107 is an add-on bottle stand for the 1107/1117 series drinking fountains with the 1920 bottle filler installed option. Once installed, the user can place their bottle on the stand allowing the bottle to be filled with one hand (either by using the push button, or the motion-activated operation). The stand is made of 304 stainless-steel with a satin finish, and is easily installed (see video under Resources).

The Haws BTL1001 is an add-on bottle stand for the 1001/1011 series drinking fountains with the 1920 bottle filler option. Once installed, the user can place their bottle on the stand allowing the bottle to be filled with one hand (either by using the push button, or the motion-activated operation). The stand is made of 304 stainless-steel with a satin finish, and is easily installed (see video under Resources).

Trouble viewing this website?

Without an up-to-date browser, you may have trouble with some of our features.

Update Now

Edge

Firefox

Chrome