Model HS12 in-wall mounting frame provides the maximum support and facilitates the installation of dual bubbler RIVIVE™ series fountains and bottle fillers. Mounted during “rough-in” phase of construction, this mounting frame allows the dual fountains to be easily and quickly installed.

• One-piece 12 gauge heavy duty mounting plate is welded to the 18 gauge wall frame
• Heavy gauge galvanized steel construction provides a solid support system for these dual bubbler fountains that is not only sturdy but provides a certain amount of corrosion resistance as well.
• Wall opening size required is 31-1/8″ wide, 47-7/8″ high, and 6″ deep (75.1 x 121.6 x 15.2 cm)
• Power cord included

Model HS11 in-wall mounting frame provides the maximum support and facilitates the installation of single bubbler Rivive series fountains and bottle fillers. Mounted during “rough-in” phase of construction, this mounting frame allows the single bubbler fountains to be easily and quickly installed.

• One-piece 12 gauge heavy duty mounting plate is welded to the 18 gauge wall frame
• Heavy gauge galvanized steel construction provides a solid support system for these single bubbler fountains that is not only sturdy but provides corrosion resistance as well.
• Wall opening size required is 18-5/8″ wide, 47-7/8″ high, and 6″ deep (47.3 x 121.6 x 12.7 cm)
• Power cord included

The Haws 7501 Config STD-9083 compact portable eyewash is a 9-gallon (34.1 L) capacity gravity operated portable eyewash that supplies a continuous flow of water for a full 15 minutes at .4 gpm. This unit is a cost-effective solution ideal for locations without access to potable water, including temporary decontamination sites, temporary treatment facilities, and short-term job sites. The 9083 cleansing stick provides clean water and ANSI compliance in equipment up to 15 gallons (60 L) for up to three years when serviced just once annually.

• Featuring a FDA approved high-density green polyethylene tank that is easily activated by pulling the yellow activation arm down to the open position
• A wide-fill opening with a securely threaded cap, and a pronounced ‘Max Fill’ line permits easy inspection, cleaning and filling
• Relocation is simple due to ‘Lift Here’ graphics, easily mounted bracket (included) and light design of this 9-gallon (34.1 L) portable
• Measurements: 14-1/2″ high, 22″ wide, 10-1/8″ (36.8 x 55.9 x 25.7 cm) deep. *Note: Unit must be wall hung

Certified by CSA to meet the ANSI/ISEA Z358.1 Standard for Emergency Eyewash and Shower Equipment.

The multi bubbler Haws 1435-1920W vandal-resistant enameled iron, drinking fountain with bottle filler incorporates patented stainless steel, push button activated, valve assemblies allowing for front access stream adjustments as well as cartridge and strainer access. This wall mounted fountain offers the ‘only’ all stainless-steel valve body that is machined out of solid bar stock, is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer, and has front access to the water stream height adjustment for easy maintenance without having to remove the valve.

• Optional 3000 gallon water filter available (model 6480)
• Only stainless steel valve body that is machined out of solid bar stock
• 100% lead-free waterways
• Vandal resistant components include the bubblers, buttons, drain and bottom plates
• 1 gpm (3.78 L) bottle filler laminar flow
• Easy maintenance with front access to valve adjustment and cartridge replacement
• Gleaming white enameled iron construction provides this fountain with a bullet proof durability hidden beneath its elegant appeal
• Soft rounded corners prevent mishaps and other accidents that may occur once the fountain is installed
• Triple bubbler heads locked to main bowl prevent against vandals and provide efficient water flow in high traffic areas
• The bottle filler requires a mounting plate; either the 6700 in-wall or the 6700R on-wall support plate. (See options below)

Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.

• Note: Enameled iron bowls are shipped without the hardware mounted. Hardware to be mounted by installer.

The multi bubbler Haws 1435-1920WHO vandal-resistant enameled iron, touchless drinking fountain with bottle filler incorporates a sensor operated stainless steel solenoid valve controlled by a transformer for hands-free operation on the bottle filler, and offers the ‘only’ all stainless-steel valve body that is machined out of solid bar stock on the fountain. It is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer and has front access to the water stream height adjustment for easy maintenance without having to remove the valve.

• Optional 3000 gallon water filter available (model 6480)
• Only stainless steel valve body that is machined out of solid bar stock
• 100% lead-free waterways
• Vandal resistant components include the bubblers, buttons, drain and bottom plates
• 1 gpm (3.78 L) bottle filler laminar flow
• Gleaming white enameled iron construction provides this fountain with a bullet proof durability hidden beneath its elegant appeal
• Touchless operation for safety and peace of mind on the bottle filler
• 30-second obstruction time-out to reduce tampering of sensor
• Soft rounded corners prevent mishaps and other accidents that may occur once the fountain is installed
• Triple bubbler heads locked to main bowl prevent against vandals and provide efficient water flow in high traffic areas
• The bottle filler requires a mounting plate; either the 6700 in-wall or the 6700R on-wall support plate. (See options below)

Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.

• Note: Enameled iron bowls are shipped without the hardware mounted. Hardware to be mounted by installer.

The multi-bubbler Haws 1430-1920WHO vandal-resistant enameled iron drinking fountain and touchless bottle filler incorporates a sensor operated stainless steel solenoid valve controlled by a transformer for hands-free operation on the bottle filler, and offers the ‘only’ all stainless-steel valve body that is machined out of solid bar stock on the fountain. It is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer and has front access to the water stream height adjustment for easy maintenance without having to remove the valve. Equipped with vandal resistant components, this fountain is not easily disrupted, quickly discouraging vandals.

• Optional 3000 gallon water filter available (model 6480)
• Only stainless steel valve body that is machined out of solid bar stock
• 100% lead-free waterways
• Vandal resistant components include the bubblers, buttons, drain and bottom plate
• 30-second obstruction time-out to reduce tampering of sensor
• Gleaming white enameled iron construction provides this fountain with a bullet proof durability hidden beneath its elegant appeal
• 1 gpm (3.78 L) bottle filler laminar flow
• Easy maintenance with front access to valve adjustment and cartridge replacement
• Soft rounded corners prevent mishaps and other accidents that may occur once the fountain is installed
• Dual bubbler heads locked to main bowl deter vandals and provide efficient water flow for twice the users as single bubbler fountains
• The bottle filler requires a mounting plate; either the 6700 in-wall or the 6700R on-wall support plate. (See options below)

Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.

• Note: Enameled iron bowls are shipped without the hardware mounted. Hardware to be mounted by installer.

The multi-bubbler Haws 1430-1920W vandal-resistant enameled iron drinking fountain and bottle filler uses patented stainless steel, push-button activated, valve assemblies allowing for front access stream adjustments as well as cartridge and strainer access. This wall mounted fountain offers the ‘only’ all stainless-steel valve body that is machined out of solid bar stock, is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer, and has front access to the water stream height adjustment for easy maintenance without having to remove the valve. Equipped with vandal resistant components, this fountain is not easily disrupted, quickly discouraging vandals.

• Optional 3000 gallon water filter available (model 6480)
• Only stainless steel valve body that is machined out of solid bar stock
• 100% lead-free waterways
• Vandal resistant components include the bubblers, buttons, drain and bottom plate
• Gleaming white enameled iron construction provides this fountain with a bullet proof durability hidden beneath its elegant appeal
• 1 gpm (3.78 L) bottle filler laminar flow
• Easy maintenance with front access to valve adjustment and cartridge replacement
• Soft rounded corners prevent mishaps and other accidents that may occur once the fountain is installed
• Dual bubbler heads locked to main bowl deter vandals and provide efficient water flow for twice the users as single bubbler fountains
• The bottle filler requires a mounting plate; either the 6700 in-wall or the 6700R on-wall support plate. (See options below)

Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.

• Note: Enameled iron bowls are shipped without the hardware mounted. Hardware to be mounted by installer.

The Haws 1105-1920HO vandal-resistant drinking fountain and touchless bottle filler incorporates a sensor operated stainless steel solenoid valve controlled by a transformer for hands-free operation on the bottle filler, and offers the ‘only’ all stainless-steel valve body that is machined out of solid bar stock on the fountain. It is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer and has front access to the water stream height adjustment for easy maintenance without having to remove the valve.

• Optional 3000 gallon water filter available (model 6480)
• Only stainless steel valve body that is machined out of solid bar stock
• 100% lead-free waterways
• Vandal resistant components include bubbler, button, drain and bottom plates
• 30-second obstruction time-out to reduce tampering of sensor
• 18 gauge Type 304 Stainless Steel design provides a well constructed sturdy fountain
• 1 gpm (3.78 L) bottle filler laminar flow
• Easy maintenance with front access to valve adjustment and cartridge replacement
• Beautiful satin finish resists stains and corrosion
• Soft rounded corners prevent from mishaps and other accidents that may occur once the fountain is installed
• One-piece stamped bowl makes for an aesthetically pleasing and durable design
• The bottle filler requires a mounting plate; either the 6700 in-wall or the 6700R on-wall support plate. (See options below)

Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.

The Haws 1105-1920 vandal-resistant drinking fountain and bottle filler uses patented stainless steel, push-button activated, valve assemblies allowing for front access stream adjustment as well as cartridge and strainer access. This wall mounted fountain offers the ‘only’ all stainless-steel valve body that is machined out of solid bar stock, is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer, and has front access to the water stream height adjustment for easy maintenance without having to remove the valve.

• Optional 3000 gallon water filter available (model 6480)
• Only stainless steel valve body that is machined out of solid bar stock
• 100% lead-free waterways
• Vandal resistant components include bubbler, buttons, drain and bottom plates
• 18 gauge Type 304 Stainless Steel design provides a well constructed sturdy fountain
• 1 gpm (3.78 L) bottle filler laminar flow
• Easy maintenance with front access to valve adjustment and cartridge replacement
• Beautiful satin finish resists stains and corrosion
• Soft rounded corners prevent from mishaps and other accidents that may occur once the fountain is installed
• One-piece stamped bowl makes for an aesthetically pleasing and durable design
• The bottle filler requires a mounting plate; either the 6700 in-wall or the 6700R on-wall support plate. (See options below)

Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.

The Haws 1109-1920HO ADA vandal-resistant drinking fountain and touchless bottle filler incorporates a touchless sensor operated stainless steel solenoid valve controlled by a transformer for hands-free operation on the bottle filler, and offers the ‘only’ all stainless-steel valve body that is machined out of solid bar stock on the fountain. It is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer and has front access to the water stream height adjustment for easy maintenance without having to remove the valve.

• Optional 3000 gallon water filter available (model 6480)
• Only stainless steel valve body that is machined out of solid bar stock
• 100% lead-free waterways
• Vandal resistant components include bubbler, button, drain and bottom plates
• 30-second obstruction time-out to reduce tampering of sensor
• 18 gauge Type 304 Stainless Steel design provides a well constructed sturdy fountain
• 1 gpm (3.78 L) bottle filler laminar flow
• Easy maintenance with front access to valve adjustment and cartridge replacement
• Beautiful satin finish resists stains and corrosion
• Soft rounded corners prevent from mishaps and other accidents that may occur once the fountain is installed
• One-piece stamped bowl makes for an aesthetically pleasing and durable design
• The bottle filler requires a mounting plate; either the 6700 in-wall or the 6700R on-wall support plate. (See options below)

Model meets all current Federal Regulations for the disabled including those in the Americans with Disabilities Act. Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.

The Haws 1501-1920W ADA vandal-resistant drinking fountain and bottle filler uses patented stainless steel, push-button activated, valve assemblies allowing for front access stream adjustment as well as cartridge and strainer access. This wall mounted fountain offers the ‘only’ all stainless-steel valve body that is machined out of solid bar stock, is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer, and has front access to the water stream height adjustment for easy maintenance without having to remove the valve.

• Optional 3000 gallon water filter available (model 6480)
• Only stainless steel valve body that is machined out of solid bar stock
• 100% lead-free waterways
• Vandal resistant components include the bubblers, buttons, drains and bottom plates
• White enameled-iron fountain design provides toughness for the worst of environments
• 1 gpm (3.78 L) bottle filler laminar flow
• Easy maintenance with front access to valve adjustment and cartridge replacement
• Beautiful white enamel fountain and powder-coated bottle filler combination brings pleasing aesthetics to any environment
• Soft rounded corners prevent from mishaps and other accidents that may occur once the fountain is installed
• The bottle filler requires a mounting plate; either the 6700 in-wall or the 6700R on-wall support plate. (See options below)

Model meets all current Federal Regulations for the disabled including those in the Americans with Disabilities Act. Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.

The Haws 1311-1920W ADA vandal-resistant drinking fountain and bottle filler uses patented stainless steel, push-button activated, valve assemblies allowing for front access stream adjustment as well as cartridge and strainer access. This wall mounted fountain offers the ‘only’ all stainless-steel valve body that is machined out of solid bar stock, is fully serviceable through the front of the push button assembly offering access to the water control cartridge and integral water supply strainer, and has front access to the water stream height adjustment for easy maintenance without having to remove the valve.

• Optional 3000 gallon water filter available (model 6480)
• Only stainless steel valve body that is machined out of solid bar stock
• 100% lead-free waterways
• Vandal resistant components include the bubbler, buttons, drain and bottom plates
• White enameled-iron fountain design provides toughness for the worst of environments
• 1 gpm (3.78 L) bottle filler laminar flow
• Easy maintenance with front access to valve adjustment and cartridge replacement
• Beautiful white enamel fountain and powder-coated bottle filler combination brings pleasing aesthetics to any environment
• Soft rounded corners prevent from mishaps and other accidents that may occur once the fountain is installed
• The bottle filler requires a mounting plate; either the 6700 in-wall or the 6700R on-wall support plate. (See options below)

Model meets all current Federal Regulations for the disabled including those in the Americans with Disabilities Act. Haws manufactures drinking fountains, faucets and electric water coolers to be lead-free by all known definitions including NSF/ANSI/CAN 61- Section 9, NSF/ANSI/CAN 372, California Proposition 65, and the Federal Safe Drinking Water Act. Product is compliant to California Health and Safety Code 116875 (AB 1953-2006), and 116876 (AB 100) “NSF/ANSI/CAN 61: Q ≤ 1”.

Trouble viewing this website?

Without an up-to-date browser, you may have trouble with some of our features.

Update Now

Edge

Firefox

Chrome